Search Results

Abstract Off-highway equipment are subjected to diverse environmental conditions, severe duty cycles, and multiple simultaneous operations. Due to its continuous, high-power adverse operating conditions, equipment are exposed to high thermal loads, which result in the deterioration of its performance and efficiency. This article describes a model-based system simulation approach for thermal performance evaluation of a self-propelled off-highway vehicle. The objective of developing the simulation model including thermal fidelity is to quantify the impact of thermal loads on vehicular system/subsystems performance. This article also describes the use of simulation models for driving architectural design decisions and virtual test replication in all stages of product development.

Abstract Environmental protection and the depletion of nonrenewable energy sources necessitate the search for the replacement of, among others, diesel fuel (Df) in diesel engines with renewable fuel without major structural changes. For this reason, vegetable oils are of interest as a possible fuel for this type of engine. Unfortunately, the physicochemical properties of vegetable oils differ significantly from Df. In addition to the boiling and freezing points, these properties include viscosity, density, and surface tension as well as wetting properties. For this reason, an attempt was made to modify these properties by adding n-hexane (Hex) and ethanol (Et) to canola oil (Co). The viscosity, density, surface tension, and wetting properties of Hex and Et are significantly different from those for Co.

Abstract Uncertainty of fuel reserves, environmental crisis, and health concerns arise from transport demands and reliance on fossil fuels. Downsized gasoline turbocharged direct injection (GTDI) engines have been developed and applied to most modern gasoline vehicles, delivering superior efficiency in high-load operation, reduced friction, and weight. But fuel enrichment and late combustion phasing to mitigate knocking combustion have hindered the efficiency benefits at higher loads with high boost. Furthermore, the wide valve-overlap with a three-cylinder setup for the maximum scavenging efficiency produces bursts of short-circuit (SC) air to cause underestimation of the equivalence ratio by the oxygen sensor, resulting in higher tailpipe nitrogen oxides (NOx) emissions with three-way catalyst (TWC) exhaust aftertreatment. Reducing the valve overlap to limit short-circuiting and enrichment will recover the combustion efficiency and the engine ER, but at the cost of high knock onset.

Abstract The article discusses the possibilities of detecting defects in the marine diesel engine injection system on a selected example. Basing on statistical data, it was pointed out that these engines had a significant failure rate in relation to the failure rate of other machinery and equipment used on ships. First, it concerns damage of the elements of the injection systems. Therefore, basing on the results of the authors’ own research, the possibility of improving diagnostic methods of the injection system that can be used in the ship operation process was pointed out. First, high diagnostic effectiveness of the analysis of pressure changes measured in the injection system was pointed out here. At the same time, taking into account the difficulties of such measurement in the conditions of the ship’s power plant, it has been shown that very good diagnostic effects can be obtained by using indicator diagrams to calculate heat release characteristics.

Abstract The frequency of video-capturing collision events from surveillance systems are increasing in reconstruction analyses. The video that has been provided to the investigator may not always include a clear perspective of the relevant area of interest. For example, surveillance video of an incident may have captured a pre- or post-incident perspective that, while failing to capture the precise moment when the pedestrian was struck by a vehicle, still contains valuable information that can be used to assist in reconstructing the incident. When surveillance video is received, a quick and efficient technique to place the subject object or objects into a three-dimensional environment with a known rate of error would add value to the investigation.

Abstract Neutron diffraction is a powerful tool for noninvasive and nondestructive characterization of materials and can be applied even in large devices such as internal combustion engines thanks to neutrons’ exceptional ability to penetrate many materials. While proof-of-concept experiments have shown the ability to measure spatially and temporally resolved lattice strains in a small aluminum engine on a timescale of minutes over a limited spatial region, extending this capability to timescales on the order of a crank angle degree over the full volume of the combustion chamber requires careful design and optimization of the engine structure to minimize attenuation of the incident and diffracted neutrons to maximize count rates.

Abstract To assess the effect of the presence of carbon dioxide (CO2) in natural gases on the knock resistance of fuel, the knock behavior of a lean-burn, high-speed medium Brake Mean Effective Pressure (BMEP) Combined Heat and Power (CHP) engine fueled with CH4 + 8 mole% C3H8 mixtures. The engine experiments are supplemented with ignition measurements and simulations of ignition and cylinder processes for various fuel compositions. The engine results show that increasing the fraction of CO2 results in an increase in knock resistance. The analysis of simulations of cylinder processes shows that for binary mixtures (CH4/CO2) and ternary mixtures (CH4/C3H8/CO2) the increase in knock resistance with increasing CO2 fraction is caused by the reduction in peak pressure/temperature, which consequently increases the autoignition delay time of the mixture.

Abstract The article describes the results achieved in developing a new diesel combustion system for passenger car application that, while capable of high power density, delivers excellent fuel economy through a combination of mechanical and thermodynamic efficiencies improvement. The project stemmed from the idea that, by leveraging the high fuel injection pressure of last generation common rail systems, it is possible to reduce the engine peak firing pressure (pfp) with great benefits on reciprocating and rotating components’ light-weighting and friction for high-speed light-duty engines, while keeping the power density at competitive levels. To this aim, an advanced injection system concept capable of injection pressure greater than 2500 bar was coupled to a prototype engine featuring newly developed combustion system. Then, the matching among these features has been thoroughly experimentally examined.

Abstract Combustion engines and liquid fuels are likely to continue playing a central role in freight transportation with renewable fuels reducing carbon emissions. Ethanol and methanol are future renewable fuels with a knock resistance that make them suitable for heavy-duty (HD) spark ignition (SI) engines. This simulation work focuses on the potential for improving the efficiency of an ethanol- and methanol-fueled HD SI engine using early intake valve closing Miller valve timing. With Miller valve timing, the expansion ratio and thermodynamic efficiency can be increased while maintaining the same effective compression ratio. However, Miller timing requires increased boost pressure to retain the same trapped air mass and also suffers from reduced in-cylinder turbulence.

Abstract Different aftertreatment systems consisting of a combination of selective catalytic reduction (SCR) and SCR catalyst on a diesel particulate filter (DPF) (SCR-F) are being developed to meet future oxides of nitrogen (NOx) emissions standards being set by the Environmental Protection Agency (EPA) and the California Air Resources Board (CARB). One such system consisting of a SCRF® with a downstream SCR was used in this research to determine the system NOx reduction performance using experimental data from a 2013 Cummins 6.7L ISB diesel engine and model data. The contribution of the three SCR reactions on NOx reduction performance in the SCR-F and the SCR was determined based on the modeling work. The performance of a SCR was simulated with a one-dimensional (1D) SCR model. A NO2/NOx ratio of 0.5 was found to be optimum for maximizing the NOx reduction and minimizing NH3 slip for the SCR for a given value of ammonia-to-NOx ratio (ANR).

Abstract High load (18 bar IMEP) dual fuel combustion of a premixed natural gas/air charge ignited by directly injected diesel fuel was studied in a large bore gas engine. A nozzle design with low flow rate was installed to inject a small diesel volume (10.4 mm3) equal an energetic amount of about two percent. The effect of compression end temperature on ignition and combustion was investigated using valve timings with early IVC (Miller) and maximum charging efficiency (MaxCC). Furthermore, the engine speed was reduced (1500 rpm to 1000 rpm) for the Miller valve timing to analyze the impact of the chemical time scale on the combustion process. During all experiments, the cylinder charge density was kept constant adjusting the intake pressure and the resulting air mass flow.

Abstract The present study evaluates the effect of engine speed, exhaust gas recirculation (EGR), and compression ratio on conventional diesel combustion (CDC) and two isobaric combustion cases, by utilizing multiple injection strategies. The experiments were conducted in a Volvo D13C500 single-cylinder, heavy-duty engine, fuelled with standard European Union (EU) diesel fuel. The engine was operated at three different speeds of 1200, 1500, and 1800 revolutions per minute (rpm). For each engine speed and combustion cases, the EGR rate was varied from 0% to 40%. The low-pressure isobaric combustion (IsoL) and high-pressure isobaric combustion (IsoH) were maintained at peak cylinder pressure (PCP) of 50 and 68 bar, respectively, which was representative of the peak motoring pressure (PMP) and PCP of CDC. This was possible by adjusting the intake air pressure to 1.7 and 2.3 bar—absolute for IsoL and IsoH, respectively, at 1200 rpm.

Abstract The causes of failure due to cracking in the resistance spot welding of the advanced high-strength steels dual-phase 590 (DP590) were investigated using scanning electron microscopy (SEM), optical microscopy, and the tensile-shear test. The results showed that by increasing the current amount, the formation of the melting zone occurred in the heat-affected zone, leading to the cracking in this area, reducing the tensile strength and decreasing the mechanical properties; the initiation and growth of cracking and failure in this region also happened. In the heat-affected zone, by increasing the current amount with the softening phenomenon, the recrystallized coarse grains also occurred, eventually resulting in the loss of mechanical properties. The results of the tensile-shear test also indicated that by increasing the current up to 12 kA, the strength was raised, but the ductility was reduced.

Abstract This study implements Flame Image Velocimetry (FIV), a diagnostic technique based on post-processing of high-speed soot luminosity images, to show the in-flame flow field development impacted by after-injection in a single-cylinder, small-bore optical diesel engine. Two after-injection cases with different dwell times between the main injection and after-injection, namely, close-coupled and long-dwell, as well as a main-injection-only case are compared regarding flow fields, flow vector magnitude, and turbulence intensity distribution. For each case, high-speed soot luminosity movies from 100 individual combustion cycles are recorded at a high frame rate of 45 kHz for FIV processing. The Reynolds decomposition using a spatial filtering method is applied to the obtained flow vectors so that bulk flow structures and turbulence intensity distributions can be discussed.

Abstract The increase in worldwide awareness of environmental issues has necessitated the air transport industry to drastically reduce carbon dioxide emissions. To meet this goal, one solution is the electrification of aircraft propulsion systems. In particular, single-aisle aircraft with partial turboelectric propulsion with approximately 150 passenger seats in the 2030s are the focus. To develop a single-aisle aircraft with partial turboelectric propulsion, an air-cooled interior permanent magnet (IPM) motor with an output of 2 MW is desired. In this article, mathematical system equations that describe heat transfer inside the target air-cooled IPM motor are formulated, and their mathematical analytical solutions are obtained.

Abstract TOC

Abstract TOC

Abstract TOC

Abstract TOC

Abstract TOC